The Home Assistant developers challenged themselves: what would the perfect home automation hub look like. Not just software, but also hardware and looks.
The result is this limited edition Home Assistant Blue bundle. Hardware that is affordable and fast, packed in a gorgeous case and powered by the most powerful home automation software on the planet: Home Assistant.
Back in stock for immediate dispatch!
The Blue Vision
Home Assistant Blue is the perfect platform to run Home Assistant, with the perfect look.
Easy to use
Powered by the Home Assistant Operating System, getting started is as easy as plugging in the network and power cables and opening up the Home Assistant mobile app to get started.
Home Assistant Blue comes with 128GB of eMMC storage. That’s the same type of storage your phone uses. A sudden loss of power won’t fry it.
Home Assistant Blue looks as good as the software that runs it: eye-catching. Hahn Werke designed a beautiful aluminium case.
All software that runs on Home Assistant Blue is open source. Including all the hardware drivers. BayLibre will be used to fix bugs and get it merged upstream in the Linux kernel!
What’s in the bundle
- Limited edition Home Assistant Blue case
- ODROID N2+ with 4GByte RAM
- 128GB eMMC storage with Home Assistant pre-installed
- Real Time Clock backup battery
- Power adapter (12V/2A)
Home Assistant Blue is future proof
Home Assistant Blue is powered by a powerful processor, good amount of memory and comes with a large storage.
It allows you to easily run Home Assistant, a couple of add-ons and then a couple more. It will be able to easily integrate thousands of devices and run thousands of automations.
|Form Factor||Dimensions: 105mm x 98mm x 33mm approximately.
Weight: 300g including heatsink and HomeAssistant Blue metal cases
|Processor||Amlogic S922X Processor (12nm fab) Quad-core Cortex-A73(up to 2.4Ghz) and Dual-core Cortex-A53 (up to 2Ghz)
ARMv8-A architecture with Neon and Crypto extensions
Mali-G52 GPU with 6 x Execution Engines (800Mhz)
|Memory||DDR4 4GiB with 32-bit bus width. Data rate: 2640 MT/s (PC4-21333 grade)
1.2Volt low power design
|Storage||1 x eMMC connector (128GB module preinstalled ) 1 x microSD slot (DS/HS modes up to UHS-I SDR104)|
|Networking||1 x GbE LAN ports (RJ45, supports 10/100/1000 Mbps)– Realtek RTL8211F (Ethernet transceiver)
– LED indicators
* Green LED: Flashing by data traffics at 100Mbps connection
* Amber LED: Flashing by data traffics at 1000Mbps connection
Optional WiFi USB adapters
|Video||1 x HDMI 2.0 (up to 4K@60Hz with HDR, CEC, EDID)|
|Audio||1 x Stereo Audio line-out (3.5mm jack) 1 x HDMI digital output
1 x Optional SPDIF optical output
|External I/O||4 x USB 3.0 Host ports (shares one single root hub) 1 x USB 2.0 OTG port for Host or Device mode. (No power input)
1 x Debug serial console (UART)
1 x Peripheral Expansion Header (40-pin, 2.54mm pitch)
– 2 x DC 5V, 2 x DC 3.3V, 1 x DC 1.8V, 8 x GND
– 1 x SPI
– 1 x UART
– 2 x I2C
– 25 x GPIO (Max)
– 2 x ADC input (10bit, 1.8V Max)
– All 3.3V I/O signal level except for ADC input at max 1.8Volt.
|Other features||On board RTC(Real Time Clock) IC keeps time up to several years with a preinstalled CR2032 battery.
8MiB SPI Flash for boot manager
IR receiver for remote controller
Built with a large passive heatsink
System LEDS Indicators:
– Red (PWR) – Solid light when DC power is connected
– Blue (ALIVE) – Flashing like heartbeat while Kernel is running.
Active Cooling Fan Connector (5V 2-pin)
– Connector (2-pin, 1.25mm pitch)
|Power||1 x DC jack : outer (negative) diameter 5.5mm, inner(positive) diameter 2.1mmDC 7.5V ~ 18V (up to 25W)
– DC 12V/2A power adapter is included
– IDLE : ≃ 2.2W (Performance governor)
– CPU Stress : ≃ 5.9W (@2016/2208MHz), 6.2W (@2016/2400MHz)
– Power-off : ≃ 0.2W
|Applicable Dangerous Goods Regulations||Not Applicable|